diff options
Diffstat (limited to 'doc/userguide')
| -rw-r--r-- | doc/userguide/control-center.docbook | 4 | ||||
| -rw-r--r-- | doc/userguide/index.docbook | 8 | ||||
| -rw-r--r-- | doc/userguide/kde-for-admins.docbook | 12 | ||||
| -rw-r--r-- | doc/userguide/switching-sessions.docbook | 6 |
4 files changed, 15 insertions, 15 deletions
diff --git a/doc/userguide/control-center.docbook b/doc/userguide/control-center.docbook index e89441cea..06e862f3e 100644 --- a/doc/userguide/control-center.docbook +++ b/doc/userguide/control-center.docbook @@ -878,8 +878,8 @@ configuration files for a &Linux; kernel. This configurator is compatible with k </varlistentry> <varlistentry> <term><guilabel>Login Manager</guilabel></term> -<listitem><para>This module allows you to configure the &kde; login manager, &kdm;. &kdm; is -a powerful login manager with a large range of options. It supports user switching, remote graphical logins and has a fully customizable appearance. For more information, see the &kdm; handbook. </para></listitem> +<listitem><para>This module allows you to configure the &kde; login manager, &tdm;. &tdm; is +a powerful login manager with a large range of options. It supports user switching, remote graphical logins and has a fully customizable appearance. For more information, see the &tdm; handbook. </para></listitem> </varlistentry> <varlistentry> <term><guilabel>Paths</guilabel></term> diff --git a/doc/userguide/index.docbook b/doc/userguide/index.docbook index e9fb63f47..44a0f5d90 100644 --- a/doc/userguide/index.docbook +++ b/doc/userguide/index.docbook @@ -357,7 +357,7 @@ programs here (and not links to removable media, like CDs).</para> </sect1info> <title>Logging In and Logging Out</title> -<para>Basic KDM & starttde stuff.</para> +<para>Basic TDM & starttde stuff.</para> <!-- Not sure what exactly to say about starttde and where to say it --> <!-- (Phil) --> <para>There are two ways to log into &kde;: graphically and via the @@ -366,7 +366,7 @@ command line. We'll look at them both briefly:</para> <sect2 id="logging-in-graphically"> <title>Logging in Graphically</title> <indexterm><primary>login</primary></indexterm> -<indexterm><primary>&kdm;</primary></indexterm> +<indexterm><primary>&tdm;</primary></indexterm> <para>If you see a screen a little bit like the one below when you start up your computer, then you are all set for logging in @@ -410,9 +410,9 @@ for now, hit <guibutton>Cancel</guibutton>.</para> <itemizedlist> <title>Related Information</title> -<listitem><para>The &kdm; Handbook has information about using and setting up +<listitem><para>The &tdm; Handbook has information about using and setting up the &kde; graphical login manager. You can read it in &khelpcenter; or -by entering <userinput>help:/kdm</userinput> in &konqueror;'s +by entering <userinput>help:/tdm</userinput> in &konqueror;'s <guilabel>Location</guilabel> bar.</para> </listitem> </itemizedlist> diff --git a/doc/userguide/kde-for-admins.docbook b/doc/userguide/kde-for-admins.docbook index 029eedb8a..5fb497f95 100644 --- a/doc/userguide/kde-for-admins.docbook +++ b/doc/userguide/kde-for-admins.docbook @@ -781,11 +781,11 @@ Auto Save Interval=25 <sect1 id="kde-startup-sequence"> <title>&kde; Startup Sequence</title> -<sect2 id="kdm"> -<title>&kdm;</title> +<sect2 id="tdm"> +<title>&tdm;</title> <para>Always runs as <systemitem class="username">root</systemitem>! Uses -<filename>$<envar>TDEDIR</envar>/share/config/kdmrc</filename> and +<filename>$<envar>TDEDIR</envar>/share/config/tdmrc</filename> and <filename>/etc/X11/xdm/Xservers</filename>. The latter contains entries like:</para> @@ -796,7 +796,7 @@ like:</para> <para>Relevant startup files are also: </para> <simplelist> <member> -[X-*-Core] section in <filename>kdmrc</filename> +[X-*-Core] section in <filename>tdmrc</filename> </member> <member> Setup - <filename>/etc/X11/xdm/Xsetup</filename> @@ -828,7 +828,7 @@ Reset - <filename>/etc/X11/xdm/Xreset</filename> - after session finished <para>The &kde; startup sequence starts with the <filename>starttde</filename> script. In most cases this script gets called -from the display manager (&kdm;) once the user has been authenticated. Their +from the display manager (&tdm;) once the user has been authenticated. Their are two very important lines in the <filename>starttde</filename> script:</para> @@ -2107,7 +2107,7 @@ screen</para></listitem> <varlistentry> <term><option>start_new_session</option></term> <listitem><para>Whether the user may start a second X session (see also -&kdm;)</para></listitem> +&tdm;)</para></listitem> </varlistentry> <varlistentry> <term><option>opengl_screensavers</option></term> diff --git a/doc/userguide/switching-sessions.docbook b/doc/userguide/switching-sessions.docbook index d869d0808..2f27871d9 100644 --- a/doc/userguide/switching-sessions.docbook +++ b/doc/userguide/switching-sessions.docbook @@ -32,7 +32,7 @@ save documents) and let her or him log in.</para> you will find a <guisubmenu>Switch User</guisubmenu> submenu. It contains the command to lock the current and start a new session which means that your desktop will start the screensaver and after a few seconds can log in -with KDM as always. The <guimenuitem>Start New Session</guimenuitem> entry +with TDM as always. The <guimenuitem>Start New Session</guimenuitem> entry skips the activation of your screensaver.</para> <para>Once you have running more than one session you can either choose to @@ -53,8 +53,8 @@ User...</guibutton> button and log into another session.</para> </varlistentry> <varlistentry> -<term>Switch Session in &kdm;</term> -<listitem><para>If you are in &kdm; and want to switch to another active +<term>Switch Session in &tdm;</term> +<listitem><para>If you are in &tdm; and want to switch to another active session you can press the <guibutton>Menu</guibutton> button and choose <guisubmenu>Switch User</guisubmenu> which is mainly the same as described above.</para> |