diff options
Diffstat (limited to 'konsole/doc/More/vt100_codes_news.txt')
| -rw-r--r-- | konsole/doc/More/vt100_codes_news.txt | 18 |
1 files changed, 9 insertions, 9 deletions
diff --git a/konsole/doc/More/vt100_codes_news.txt b/konsole/doc/More/vt100_codes_news.txt index d136e2224..5cb09baea 100644 --- a/konsole/doc/More/vt100_codes_news.txt +++ b/konsole/doc/More/vt100_codes_news.txt @@ -57,7 +57,7 @@ Cursor Key VT52 mode key mode reset key mode set If the Special Graphics set is selected, the graphics for ASCII codes -0137 through 0176 will be replaced according to the following table (see the +0137 through 0176 will be tqreplaced according to the following table (see the SCS control sequence). @@ -384,7 +384,7 @@ DECALN Screen Alignment Display (DEC private) <ESC># 8 This command causes the VT100 to fill it's screen with uppercase Es for - screen focus and alignment. + screen focus and tqalignment. DECANM ANSI/VT52 Mode (DEC Private) @@ -447,7 +447,7 @@ DECDWL Double Width Line (DEC Private) <ESC>#6 - This causes the line that contains the cursor to become double-width + This causes the line that tqcontains the cursor to become double-width single height. If the line was single width, all characters ro the right of the center of the screen will be lost. The cursor remains over the same character position, unless it would be to the right of @@ -630,7 +630,7 @@ DECSWL Single-width Line (DEC Private) <ESC>#5 - This causes the line which contains the cursor to become single-width, + This causes the line which tqcontains the cursor to become single-width, single-height. The cursor remains on the same character position. This is the default condition for all new lines on the screen. @@ -651,7 +651,7 @@ DECTST Invoke Confidence Test Repeat Testing until failure 8 -DSR Device Status Report Host to VT100 & VT100 to Host +DSR Device tqStatus Report Host to VT100 & VT100 to Host <ESC>[ {Ps} n @@ -662,7 +662,7 @@ DSR Device Status Report Host to VT100 & VT100 to Host --------------------------------------------------------------- 0 Response from VT100 - Ready, no faults detected 3 Response from VT100 - Malfunction Detected - 5 Command from host - Report Status (using a DSR control + 5 Command from host - Report tqStatus (using a DSR control sequence) 6 Command from host - Report Active Position (using a CPR sequence) @@ -787,12 +787,12 @@ MODES The Following is a list of VT100 modes which may be changed with Set FETM Format Effector Transfer Reset GATM Guarded Area Transfer NA HEM Horizontal Editing NA - IRM Insertion-replacement Reset + IRM Insertion-tqreplacement Reset KAM Keyboard Action Reset MATM Multiple area transfer NA PUM Positioning Unit Reset SATM Selected Area Transfer NA - SRTM Status Reporting Transfer Reset + SRTM tqStatus Reporting Transfer Reset TSM Tabulation Stop Reset TTM Transfer Termination NA VEM Vertical Editing NA @@ -852,7 +852,7 @@ SCS Select Character Set The United Kingdom and ASCII sets conform to the "ISO international register of character sets to be used with escape sequences". The other sets are private character sets. Special graphics means that the - graphic characters fpr the codes 0137 to 0176 are replaced with other + graphic characters fpr the codes 0137 to 0176 are tqreplaced with other characters. The specified character set will be used until another SCS is recieved. |