diff options
Diffstat (limited to 'konsole/doc/More/vt100_reference_card.txt')
| -rw-r--r-- | konsole/doc/More/vt100_reference_card.txt | 215 |
1 files changed, 215 insertions, 0 deletions
diff --git a/konsole/doc/More/vt100_reference_card.txt b/konsole/doc/More/vt100_reference_card.txt new file mode 100644 index 000000000..e80ea1325 --- /dev/null +++ b/konsole/doc/More/vt100_reference_card.txt @@ -0,0 +1,215 @@ +Article 248 of comp.terminals: +Newsgroups: comp.terminals +Path: cs.utk.edu!gatech!udel!bogus.sura.net!opusc!usceast!chan +From: chan@ece.scarolina.edu (Simon Chan) +Subject: VT100 Reference Card !! ( if you are looking for....) +Message-ID: <chan.728236678@hertz> +Keywords: vt100 terminal escape codes +Sender: usenet@usceast.cs.scarolina.edu (USENET News System) +Organization: USC Department of Computer Science +Date: 28 Jan 93 15:57:58 GMT +Lines: 162 + + + +Taken from VT100 Programming Reference Card (DIGITAL) + +ANSI Compatible Mode + + Cursor Movement Commands + Cursor up ESC [ Pn A + Cursor down ESC [ Pn B + Cursor forward (right) ESC [ Pn C + Cursor backward (left) ESC [ Pn D + Direct cursor addressing ESC [ Pl; Pc H or + ESC [ Pl; Pc f + Index ESC D + Next Line ESC E + Reverse index ESC M + Save cursor and attributes ESC 7 + Restore cursor and attributes ESC 8 + * Pn = decimal parameter in string of ASCII digits.(default 1) + * Pl = line number (default 0); Pc = column number (default 0) + + Line Size (Double-Height and Double-Width) Commands + Change this line to double-height top half ESC # 3 + Change this line to double-height bottom half ESC # 4 + Change this line to single-width single-height ESC # 5 + Change this line to double-width single-height ESC # 6 + + Character Attributes + ESC [ Ps;Ps;Ps;...,Ps m + Ps = 0 or None All Attributes Off + 1 Bold on + 4 Underscore on + 5 Blink on + 7 Reverse video on + Any other parameter values are ignored. + + Erasing + From cursor to end of line ESC [ K or ESC [ 0 K + From beginning of line to cursor ESC [ 1 K + Entire line containing cursor ESC [ 2 K + From cursor to end of screen ESC [ J or ESC [ 0 J + From beginning of screen to cursor ESC [ 1 J + Entire screen ESC [ 2 J + + Programmable LEDs + ESC [ Ps;Ps;...Ps q + Ps = 0 or None All LEDs Off + 1 L1 on + 2 L2 on + 3 L3 on + 4 L4 on + Any other parameter values are ignored. + + Character Set (G0 and G1 Designators) + Charactor Set G0 Designator G1 Designator + United Kingdom (UK) ESC ( A ESC ) A + United States (USASCII) ESC ( B ESC ) B + Special graphics characters ESC ( 0 ESC ) 0 + and line drawing set + Alternate character ROM ESC ( 1 ESC ) 1 + Alternate character ROM ESC ( 2 ESC ) 2 + special graphics characters + + Scrolling Region + ESC [ Pt ; Pb r + Pt is the number of the top line of the scrolling region; + Pb is the number of the bottom line of the scrolling region + and must be greater than Pt. + (The default for Pt is line 1, the default for Pb is the end + of the screen) + + TAB stops + Set tab at current column ESC H + Clear tab at curent column ESC [ g or ESC [ 0 g + Clear all tabs ESC [ 3 g + + Modes + To Set To Reset + Mode Name Mode Sequence Mode Sequence + Line feed/new line New line ESC [20h Line feed ESC [20l + Cursor key mode Application ESC [?1h Cursor ESC [?l + ANSI/VT52 mode ANSI N/A VT52 ESC [?2l + Column mode 132 Col ESC [?3h 80 Col ESC [?3l + Scrolling mode Smooth ESC [?4h Jump ESC [?4l + Screen mode Reverse ESC [?5h Normal ESC [?5l + Origin mode Relative ESC [?6h Absolute ESC [?6l + Wraparound On ESC [?7h Off ESC [?7l + Auto repeat On ESC [?8h Off ESC [?8l + Interlace On ESC [?9h Off ESC [?9l + Graphic proc. option On ESC 1 Off ESC 2 + Keypad mode Application ESC = Numeric ESC > + + Reports + Cursor Position Report + Invoked by ESC [ 6 n + Response is ESC [ Pl; Pc R + * Pl = line number; Pc = column number + + Status Report + Invoked by ESC [ 5 n + Response is ESC [ 0 n (terminal ok) + ESC [ 3 n (terminal not ok) + + What Are You + Invoked by ESC [ c or ESC [ O c + Response is ESC [ ?1 ; Ps C + Ps = 0 Base VT100, no options + 1 Processor option (STP) + 2 Advanced Video option (AVO) + 3 AVO and STP + 4 Graphocs processor option (GO) + 5 GO and STP + 6 GO and AVO + 7 GO, STP, and AVO + Alternately invoked by ESC Z (not recommended.) Response is the same. + + Reset + ESC c + + Confidence Tests + Fill Screen with "Es" ESC # 8 + Invoke Test(s) ESC [ 2 ; Ps y + Ps = 1 Power-up self test + (ROM checksum, RAM, NVR, + keyboard and AVO if installed) + 2(loop back connector required) Data Loop Back + 4(loop back connector required) ETA Modern Control Test + 8 Repeat selected test(s) + indefinitely + (until failure or power off) + +VT52 Compatible Mode + Cursor Up ESC A + Cursor Down ESC B + Cursor Right ESC C + Cursor Left ESC D + Select Special Graphics character set ESC F + Select ASCII character set ESC G + Cursor to home ESC H + Reverse line feed ESC I + Erase to end of screen ESC J + Erase to end of line ESC K + Direct cursor address ESC Ylc (see note 1) + Identify ESC Z (see note 2) + Enter alternate keypad mode ESC = + Exit alternate keypad mode ESC > + Enter ANSI mode ESC < + + NOTE 1: Line and column numbers for direct cursor address are single + character codes whose values are the desired number plus + 37 (in Octal). Line and column numbers start at 1. + NOTE 2: Response to ESC Z is ESC / Z. + + + +-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- +Simon Chan chan@ece.scarolina.edu +Department of Electrical & Computer Engineering +Swearingen Engineering Centre +University of South Carolina +Coulmbia, South Carolina 29208 +-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- + + +Article 269 of comp.terminals: +Path: cs.utk.edu!gatech!news.ans.net!cmcl2!adm!smoke!gwyn +From: gwyn@smoke.brl.mil (Doug Gwyn) +Newsgroups: comp.terminals +Subject: Re: VT100 Reference Card !! +Keywords: vt100 terminal escape codes +Message-ID: <19629@smoke.brl.mil> +Date: 1 Feb 93 15:01:49 GMT +References: <chan.728236678@hertz> +Organization: U.S. Army Ballistic Research Lab, APG MD. +Lines: 25 + +In article <chan.728236678@hertz> chan@ece.scarolina.edu (Simon Chan) writes: +>Taken from VT100 Programming Reference Card (DIGITAL) + +Note that EK-VT100-RC-001 contains several errors and omissions. +The errors appear to all be fixed in the posted version. +Here are some additions: + + Parameters to Direct cursor addressing can be omitted if 1. + "Index" is broken if NEWLINE is enabled (set-up). + "Reverse index" scrolls up retaining the same column. + + CHARACTER SET DESIGNATORS: G0 = Shift-In, G1 = Shift-Out + +> ANSI/VT52 mode ANSI N/A VT52 ESC [?2l + ANSI/VT52 mode ANSI ESC < VT52 ESC [?2l + Modes can be combined using ";", for example "ESC [ ? 3 ; 4 ; 7 h" + + CONFIDENCE TESTS: Parameter bits are summed into one parameter. + + Hardcopy ESC # 7 + Graphic processor ON ESC 1 + Graphic processor OFF ESC 2 + +The reference card showed incorrect graphics for octal code 140; its +correct graphic is ` (accent grave). + + |