From: sherwin@royalt.enet.dec.com (Jim Sherwin) Newsgroups: comp.terminals Subject: Re: VT100 (DEC) Setup Problem (online/offline) Message-ID: <29245@nntpd.lkg.dec.com> Date: 25 Oct 91 02:02:07 GMT Organization: DEC -- Video, Image and Printer Systems Group Lines: 63 Striking the SET-UP key places you into SET-UP A mode. SET-UP A is basically your tab stops. Use the space bar to move along the ruler and strike the T key at the desired tab stop location. SET-UP B may only be entered from SET-UP A and is done be striking the 5 on the main keyboard (i.e. top-row). To exit SET-UP B strike the SET-UP key. The SET-UP parameters are as follows: Bank Position Parameters 1 1 Scroll; 0=jump; 1=smooth 1 2 Autorepeat; 0=off; 1=on 1 3 Screen; 0=dark; 1=light 1 4 Cursor; 0=underline; 1=block 2 1 Margin Bell; 0=off; 1=on 2 2 Keyclick; 0=off; 1=on 2 3 ANSI/VT52; 0=VT52; 1=ANSI 2 4 Auto XON/XOFF; 0=off; 1=on 3 1 Pound Sign; 0=octothorpe; 1=British Pound 3 2 Wrap Around; 0=off; 1=on 3 3 New Line; 0=off; 1=on 3 4 Interlace; 0=off; 1=on 4 1 Parity Sense; 0=odd; 1=even 4 2 Parity; 0=off; 1=on 4 3 Bits per Char; 0=7 bits; 1=8 bits 4 4 Power; 0=60 Hz; 1=50 Hz While in SET-UP B mode, these features are set by positioning the cursor above the feature switch, using the spacebar, and striking the 6 key on the main keyboard. To set the ANSWERBACK MESSAGE, enter SET-UP B and strike the SHIFT and A keys simultaneously. The terminal will respond with A = on the screen. Type a message delimiter character which may be any chaacter not used in the actual message. Type the ANSWERBACK MESSAGE, up to 20 characters. Type the message delimiter character. The message will disappear from the screen. You may not edit an ANSWERBACK MESSAGE. You may only supercede it with a new ANSWERBACK MESSAGE. To save the SET-UP, strike the SHIFT and S keys simultaneously, while in SET-UP mode. I hope this helps. Jim <>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<> <> "When things are going well, \ Jim Sherwin a.k.a. <> <> someone will inevitably \ sherwin@royalt.enet.dec.com <> <> experiment detrimentally." \ !decwrl!royalt.enet.dec.com!sherwin <> <> Boyle's Second Law \ sherwin%royalt.enet@decwrl.dec.com <> <>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<>-<> Article 20936 of comp.dcom.modems: Path: utkcs2!darwin.sura.net!jvnc.net!yale.edu!think.com!news.bbn.com!news.bbn.com!news From: Paul Placeway Newsgroups: comp.dcom.modems,alt.bbs Subject: Re: Detecting ANSI on a remote system Date: 11 Jul 1992 00:04:09 GMT Lines: 82 Message-ID: References: <1992Jul8.204233.13120@csusac.csus.edu> <1992Jul9.053233.11670@f109f.mil.se> NNTP-Posting-Host: bbn.com Xref: utkcs2 comp.dcom.modems:20936 alt.bbs:11447 nils@f109f.mil.se (Nils Hammar) writes: < emamid@athena.ecs.csus.edu (David Emami) writes: < >I am currently writing a communications app using TurboVision; I've got a < >view that can display ANSI, but how do I let the system that I hook up with < >that I can use ANSI codes. Most BBS's that I've tried respond with "ANSI < >detected" or "ANSI not detected" when I login using a commercial term < >program, based on the emulation I'm using. I presume that the BBS sends a < >string which I need to respond to in a certain way; what should my program < >be looking for, and how should it answer? Any help would be appreciated. < What I have been using is the function that reports the cursor position. < If you get an answer on that request that is correct, it's ANSI, or a VT100 < compatible terminal. To determine if it's a VT100 or similar, you will have < to send a second request that's only recognized by the VT100 or < similar terminals. That request will result in an answer that tells you < almost everything that you need to know about the terminal. < If this secondary request doesn't give you any response, then it's only < ANSI. This is a really nice way to find out if you can send high resolution < graphics to the caller too. What a surprise to get a hig resolution < picture on the screen when you are calling an ordinary BBS! The ANSI Device tqStatus Report (DSR) is ESC [ n where is 5 for a status report (OK reply is "ESC [ 0 n"), and 6 for report cursor position (reply is "ESC [ ; R"). ANSI (and DEC) Send Device Attributes is ESC [ c where is a number, in ASCII 0-9, and usually is 0 for the request. Here are a (small) selection of replies: what reply comments ---- ----- ----------- xterm ESC[?1;2c VT100 w/AVO MacKermit ESC[?1;2c VT102 ESC[?6c VT320 ESC[63;1;2;8;9c (These are from vttest, by Per Lindberg) vanilla VT100 ESC[?1;0c no options VT100 with STP ESC[?1;1c VT100 with AVO ESC[?1;2c could be a VT102 VT100 with STP and AVO ESC[?1;3c VT100 with GPO ESC[?1;4c VT100 with STP and GPO ESC[?1;5c VT100 with AVO and GPO ESC[?1;6c VT100 with STP, AVO and GPO ESC[?1;7c VT100 with PP and AVO ESC[?1;11c VT100 with PP, GPO and AVO ESC[?1;15c VT132 with AVO ESC[?4;2c VT132 with AVO and STP ESC[?4;3c VT132 with GPO and AVO ESC[?4;6c VT132 with GPO, AVO, and STP ESC[?4;7c VT132 with PP and AVO ESC[?4;11c VT132 with PP, GPO and AVO ESC[?4;15c VT131 ESC[?7c VT125 ESC[?12;5c VT125 also has ROM version VT125 with AVO ESC[?12;7c number, so this won't work VK100 (GIGI) ESC[?5;0c VK100 (GIGI) ESC[?5c DXterm (DEC's version of xterm) ESC[?63;1;3;4;6;8;9;15;16;29c < For this reason, I once wrote a program that convert PCX pictures < to DEC Sixel Graphics. It was interesting to view those pictures < on the screen with MS-KERMIT (which supports Sixel Graphics in colour.) < The only disadvantage was that Sixel graphics is bitmapped and slow. This is cute, but one needs to be careful about assuming what a terminal emulator will do based on what it claims to be. There are a lot of mediocre "emulations" out there. This is partially because the ANSI spec allows the terminal to do a lot of weird and unexpected things, like embedding simple control characters in the middle of an escape sequence. ("foo ^H^[^H[^H4^HCbar" should render as "foo bar". Yuck.) -- Paul Placeway